Your Cart is Empty
The SL4540 Gen8 Server is a server Purpose-Built for big data. A highly efficient converged design that delivers the right combination of capacity and performance, in the least amount of space and at lower cost, with the reliability and manageability user expect from HP ProLiant Gen8, the world's most intelligent servers.
The HP ProLiant SL4540 Gen8 Server solves the traditional structured database problems when dealing with big data. Implementing a scale-up infrastructure will invariably result in challenges of data center capacity, spiraling energy costs, infrastructure complexity and inefficiencies because today's siloed infrastructure is not optimized for scale-out server workloads driven by big data. The SL4540 Gen8 Server is a server purpose-built for big data.
Intel Xeon Processor E5-2400 v2 series.
HP SL4500 H220 Host Bus Adapter (HBA).
VMware support for H220 HBA.
HP DDR3-1600 low voltage memory kit.
Hard drive zoning via two P420i controller.
Processor(One of the following depending on model)
E5-2400 v2 series
Cache memory (One of the following depending on model)
Upgradeable to two processors
On system management processor
HP Integrated Lights-Out 4 (iLO 4) (Firmware: HP iLO 4)
Memory (Dedicated to each server node)
Network controller(One of the following dedicated to each server node )
Internal storage devices
Maximum internal storage
1x60 Model - 60 LFF Drives per node
2x25 Model - 25 LFF Drives per node
3x15 Model - 15 LFF Drives per node, 45 LFF Drives per chassis
Interfaces (Dedicated to each server node)
Industry standard compliance
System ships standard with 5 dual fan modules
Graphics Per node)
Integrated Matrox G200 video standard
4.3U form factor
Operating System (OS) and virtualization software support for ProLiant servers 1
Dimensions (H x W x D) Add fan extension kit (with bezel)
18.96 x 44.33 x 89.97cm (7.47 x 17.45 x 35.34 in)
Maximum (all hard drives, power supply, and processor installed): 99.8 kg (220 lb)
Rated line voltage
Rated input current
Rated input frequency
50 to 60 Hz
Rated input power
Power Supply Output (per power supply)
Rated Steady-State Power
System Inlet operating temperature
10° to 35°C (50° to 95°F) at sea level with an altitude derating of 1.8°F per every 1000 ft (1.0°C per every 304.8 m) above sea level to a maximum of 10,000 ft (3048 m), no direct sustained sunlight. Maximum rate of change is 18°F/hr (10°C/hr). The upper limit may be limited by the type and number of options installed. System performance may be reduced if operating with a fan fault or above 86°F (30°C).
System inlet non-operating temperature
-30° to 60°C (-22° to 140°F)
Operating relative humidity
10 to 90% relative humidity (Rh), 28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating relative humidity
5 to 95% relative humidity (Rh), 38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
3048 m (10,000 ft). This value may be limited by the type and number of options installed. Maximum allowable altitude change rate is 1500 ft/min (457 m/min).
9144 m (30,000 ft). Maximum allowable altitude change rate is 1500 ft/min (457 m/min).
Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
CISPR 22; EN55022; EN55024; FCC CFR 47, Pt 15; ICES-003; CNS13438; K22;K24; EN 61000-3-2; EN 61000-3-3; EN 60950-1; IEC 60950-1
*Adds to cart & you can request a quote from the cart page